X
How.com.vn is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 13 people, some anonymous, worked to edit and improve it over time.
The How.com.vn Video Team also followed the article's instructions and verified that they work.
This article has been viewed 78,582 times.
Jump rings are the small circles of wire used to attach findings to jewellery, or even make up part of the design of the jewellery itself. When you only need one or two, the price seems insignificant. However, if your project requires many jump rings or you do not know where to buy them, you might consider making them yourself. This guide will show you how.
Steps
Method 1
Method 1 of 2:
Wrapping on pliers
Select your wire. This depends almost entirely on what you want your jump ring to be like. If you are making a large jump ring, you should use thick, fairly stiff wire. If your jump ring is to be smaller, you may get away with a slightly thinner wire.
Make a loop at the end of the wire with the round nosed pliers. The loop should end with the long part of the wire just below the short part (when looking at it from the side with the pliers pointing upwards).Advertisement- Make a coil by continuing to wrap the wire around the round nosed pliers. Make sure you don't hold it so tightly it can't move up the pliers. The loops should be the same size rather than stacked in a cone shaped like the pliers.
- Continue until you have two or three more than the number of jump rings that you need. This allows for mistakes and the removal of sharp ends.
- Cut off the straight ends. This will leave you with just a coil of wire.
- Cut the jump rings. Find the point where the wire ends and cut through the loop above at this point. When you take your cutters away, you should have a jump ring attached to it. Continue this step until all of the coil has been cut into jump rings.
Make your jewellery. Have a look at How to Open a Jump Ring.Advertisement
Method 2
Method 2 of 2:
Dowel Rod method
Select the appropriate wire for your project.
Select the right sized dowel rod (or metal rod) for the project. If it's less that 3/8", you will probably have to use metal as a dowel rod will break too easily.- Make a slit in one end of the rod. This is for anchoring the wire as you wrap. This step is not essential but makes making jump rings much easier.
- Insert one end of the wire into the slit. Then begin to tightly wrap the wire around the dowel rod towards the opposite end of the slit.
Cut jump rings. Once you have wrapped enough wire on the dowel, you have several options for cutting the wire into jump rings.- One of the easier ways is to slide the wire off the rod and use parallel wire cutters to cut the rings. The drawback here is rough, sharp ends that often need to be filed/sanded.
- If you are using a wooden dowel, you can also use a jewelers saw with a 2/0 blade: move the wire up the dowel to the end, hold the dowel steady and saw a straight line through it. It is also handy to wrap a single layer of masking tape around the wire so that the rings don't fall everywhere. Slowly move the wrapped wire up the rod until you are done.
Advertisement
Community Q&A
Search
- QuestionWhere can you get jump rings?
StarHorseCommunity AnswerYou can buy jump rings at any craft store, or even somewhere like Walmart. - QuestionWhere can I buy a jump ring if I don't want to make one?
Beth H.Community AnswerIf you visit any craft store, such as Joanne Fabrics, Michael's, or Hobby Lobby; you can find hundreds of them for a few dollars.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
SubmitAdvertisement
Tips
- If the wire you choose is too thin or soft, the ends of your jump ring will pull apart. If you do not notice, you may lose your piece of jewellery, so it is always worthwhile checking your jump ring before you use it.Thanks
- If you need a large quantity of them it is easier to wrap the wire on a dowel and use a cutting blade on a Dremel to cut the links. You can make thousands in a matter of minutes using this method depending on the size of your dowel and wire.Thanks
Advertisement
Warnings
- Wear eye protection when cutting wire. Small pieces of wire are sharp and could injure your eyes.Thanks
- Sharp wire can cut. Be careful with the ends of your wire and file the sharp bits down if necessary.Thanks
Advertisement
Things You'll Need
- Wire
- Round nosed pliers
- Wire cutters
- Jewelers saw (Very efficient at cutting through portions of jump rings. There is also the added advantage of having flat edges that do not need to be filed before they are soldered. If jump rings are cut with wire cutters the ends of the rings are pinched and must be filed before they can be soldered.)
Did this article help you?
⚠️ Disclaimer:
Content from Wiki How English language website. Text is available under the Creative Commons Attribution-Share Alike License; additional terms may apply.
Wiki How does not encourage the violation of any laws, and cannot be responsible for any violations of such laws, should you link to this domain, or use, reproduce, or republish the information contained herein.
- - A few of these subjects are frequently censored by educational, governmental, corporate, parental and other filtering schemes.
- - Some articles may contain names, images, artworks or descriptions of events that some cultures restrict access to
- - Please note: Wiki How does not give you opinion about the law, or advice about medical. If you need specific advice (for example, medical, legal, financial or risk management), please seek a professional who is licensed or knowledgeable in that area.
- - Readers should not judge the importance of topics based on their coverage on Wiki How, nor think a topic is important just because it is the subject of a Wiki article.
Advertisement
